Mike@kuake.biz
Emergency measures for leakage of diesel generator sets
Article source:this site | Issuing time：2019-04-01
If the diesel generator set is used or maintained improperly, there will be problems such as oil leakage, water leakage, air leakage, etc., which will not only waste costs, but also may affect power supply accidents; therefore, the quark motor has sorted out the following emergency measures in case of leakage :
Add pad to rule leakage method:
When oil is leaking at the anti-leak gasket of the tubing joint, a layer of double-sided smooth thin plastic pads can be added on both sides of the anti-leak gasket, which can be tightly tightened to prevent leakage.
Leakage control method with paint chip liquid:
Leakage at joints of diesel fuel tank, water tank, crankcase, etc., after soaking the varnish in alcohol, apply the varnish liquid to the clean joints to cure the leakage. However, the cost of paint flakes is high, and it is generally used in emergency situations.
Oil leakage method:
When the paper gasket in the oil pan, cylinder head, gear cover, crankcase rear cover of the diesel engine leaks, as long as the paper gasket is intact and the joint surface is clean, you can apply a layer of butter on both sides of the paper gasket, and tighten the bolts. Can be leak-proof. If you change to a new paper pad, soak the new paper pad in diesel for 10 minutes before installation, then take it out and wipe it, and put a layer of butter on the joint surface before installing it.
Liquid sealant leak control method:
When solid gasket defects (such as pits, grooves, cracks) appear on the diesel engine to form interfacial leakage and destructive leakage, apply liquid sealant on the cleaned solid gasket joint surface, and the solid gasket will form a uniform, The peelable film gasket with stable and continuous adhesion can prevent all leakage.
Anaerobic glue to cure leakage method:
When there is leakage in the vent bolts, stud bolts, plugs, etc. on the diesel engine, apply anaerobic glue to the cleaned bolts, threads or screw holes to form a thin film, fill the gaps in the parts, and can withstand greater pressure , At the same time, it has strong shock resistance and sturdy function of preventing loosening. If used in the high-pressure thread of diesel engine, the leakage effect is good.
Dimensional recovery glue to cure leakage method:
When the shaft and bushing, bearing and bearing seat, valve and valve seat, self-tightening oil seal, felt cup and packing of the diesel engine leak, the size recovery glue can be applied to the cleaned and worn parts of the mating parts, etc. After curing, a thin film layer with wear resistance, heat resistance and high mechanical strength is formed, and then mechanical processing such as turning, boring, scraping and filing is performed to restore the geometric shape and matching accuracy of the parts, thereby solving the leakage problem.
Leakage control method with viscose glue:
When the body parts of the diesel engine generator set, such as blisters and pores in the fuel tank, water tank, fuel pipe, water pipe, etc., cause leakage, apply adhesive patch to the cleaned damaged area to obtain the leakage control effect.
The above measures are only temporary emergency methods. If oil, water, or gas leakage occurs, you should first contact the manufacturer or maintenance personnel to replace or repair the leaking parts.
Add pad to rule leakage method:
When oil is leaking at the anti-leak gasket of the tubing joint, a layer of double-sided smooth thin plastic pads can be added on both sides of the anti-leak gasket, which can be tightly tightened to prevent leakage.
Leakage control method with paint chip liquid:
Leakage at joints of diesel fuel tank, water tank, crankcase, etc., after soaking the varnish in alcohol, apply the varnish liquid to the clean joints to cure the leakage. However, the cost of paint flakes is high, and it is generally used in emergency situations.
Oil leakage method:
When the paper gasket in the oil pan, cylinder head, gear cover, crankcase rear cover of the diesel engine leaks, as long as the paper gasket is intact and the joint surface is clean, you can apply a layer of butter on both sides of the paper gasket, and tighten the bolts. Can be leak-proof. If you change to a new paper pad, soak the new paper pad in diesel for 10 minutes before installation, then take it out and wipe it, and put a layer of butter on the joint surface before installing it.
Liquid sealant leak control method:
When solid gasket defects (such as pits, grooves, cracks) appear on the diesel engine to form interfacial leakage and destructive leakage, apply liquid sealant on the cleaned solid gasket joint surface, and the solid gasket will form a uniform, The peelable film gasket with stable and continuous adhesion can prevent all leakage.
Anaerobic glue to cure leakage method:
When there is leakage in the vent bolts, stud bolts, plugs, etc. on the diesel engine, apply anaerobic glue to the cleaned bolts, threads or screw holes to form a thin film, fill the gaps in the parts, and can withstand greater pressure , At the same time, it has strong shock resistance and sturdy function of preventing loosening. If used in the high-pressure thread of diesel engine, the leakage effect is good.
Dimensional recovery glue to cure leakage method:
When the shaft and bushing, bearing and bearing seat, valve and valve seat, self-tightening oil seal, felt cup and packing of the diesel engine leak, the size recovery glue can be applied to the cleaned and worn parts of the mating parts, etc. After curing, a thin film layer with wear resistance, heat resistance and high mechanical strength is formed, and then mechanical processing such as turning, boring, scraping and filing is performed to restore the geometric shape and matching accuracy of the parts, thereby solving the leakage problem.
Leakage control method with viscose glue:
When the body parts of the diesel engine generator set, such as blisters and pores in the fuel tank, water tank, fuel pipe, water pipe, etc., cause leakage, apply adhesive patch to the cleaned damaged area to obtain the leakage control effect.
The above measures are only temporary emergency methods. If oil, water, or gas leakage occurs, you should first contact the manufacturer or maintenance personnel to replace or repair the leaking parts.
Quark Motor specializes in producing diesel generator sets，Volvo diesel generator set，Yuchai diesel generator set，Cummins diesel generator set，Shangchai diesel generator set，400kw Cummins diesel generator setWait for a full range of diesel generator sets, consultDiesel generator set manufacturers,to understandingdiesel generator set offer, welcome to inquire; we are a manufacturer of diesel generator sets, and we will solve your power problems in all aspects!24-hour hotline：400-966-0200,website：en.kuake.biz
闽公网安备 35098102351072号
